Download and Install OxygenOS 4.1.4 on OnePlus 3 and 3T
How To

Download and Install OxygenOS 4.1.4 on OnePlus 3 and 3T

OnePlus just announced the official OxygenOS 4.1.4 update for OnePlus 3 and 3T, which was released in India recently. This isn’t a major update, but a hotfix, solving issues like screen flickering and designed for this specific region. Since it’s an incremental update, it’s being rolled out in a phase-wise manner, over the air and a lot of users are already getting it.

On the other side, if you can stand the issue anymore and want to install OxygenOS 4.1.4 on OnePlus 3 and 3T manually, you can check out the detailed guide below, where you have all the instructions on how it can be done.

 

Please consider the following aspects before installing the update, in order to avoid any issues through the process:

  • This method is solely for the OnePlus 3 and 3T. Don’t use it on any other phones because it won’t work!
  • The process will not erase the data on the phone. However, it’s advisable to take a complete backup of the phone and just then proceed.
  • Make sure that the battery level is at least 50% charged, so you can prevent an accidental shutdown in the middle of the process.
  • Follow all the steps below correctly, otherwise you can even brick the device.
  • The ROM can also be flashed using TWRP as well.

 

Download OxygenOS 4.1.4 For OnePlus 3 and 3T

 

OxygenOS 4.14 Full ROM For OnePlus 3 – Download

OxygenOS 4.14 Full ROM For OnePlus 3T – Download

 

Install OxygenOS 4.1.4 on OnePlus 3 and 3T

 

Method 1

Step 1: Go to the phone Settings Menu > About phone > Build Number. Tap it seven times, in order to enable the Developer Options sub-menu.

Step 2: In Developer Options, look for USB Debugging and enable it.

Step 3: Download the ADB and fastboot driver, available here – Download, and install it on a PC.

Step 4: Download OxygenOS 4.1.4 ROM for OnePlus 3/3T  From above and copy it in the folder where ADB is installed.

Step 5: Turn off the phone.

Step 6: Boot it into Recovery Mode and choose the Install from ADB Sideload option.

Step 7: Connect the phone to a laptop or PC.

Step 8: Go to the ADB folder and open a command window, by pressing and holding Shift and Right click, at the same time.

Step 9: Check your connection by typing adb devicesIf it’s listed, you can flash the ROM.

Step 10: Flash OxygenOS 4.1.4 for OnePlus 3 and 3T by typing adb sideload File Name.zip

Step 11: Wait for 10 minutes, until the installation is over.

Step 12: Reboot your phone.

Method 2

Step 1: Download OxygenOS 4.1.4 for OnePlus 3/3T file from above, and save it on your phone’s memory.

Step 2: Reboot the phone into Recovery Mode, by pressing and holding Power + Volume Down button. Wait for the phone to boot into Stock Recovery.

Step 3: Select Apply Update.

Step 4: Select Choose from Internal Storage and look for the .zip file. This will begin the installation. Wait for 10 minutes, until it’s completed.

Step 5: Reboot the device.

This is how you can install OxygenOS 4.1.4 on OnePlus 3 or 3T. If you encounter any difficulties during the process, feel free to contact us, by dropping a few lines in the comments section below.

We whole heartedly encourage all of you to share your opinions, requests, queries, and any issues regarding our tutorials and other posts among everyone. Please feel free to visit our ObeyGeek forum and speak your mind.